Cursos Mikrotik -> MTCUME

MTCUME - MikroTik Certified User Management Engineer

Modulo 1

PPP

  • PPP Profile + LAB
    • Local and Remote addresses
    • Incoming/Outgoing Filters
    • Address List
    • Change TCP-MSS
    • Use Encryption
    • Session Timeout
    • Rate-Limit configuration
    • Only-one setting
  • PPP Secret + LAB
    • Service and Profile
    • Local and Remote address
    • Routes configuration
    • Limit Bytes In/Limit Bytes Out configuration




  • IP Pool
    • Set addresses ranges
    • Next Pool options






Modulo 2

PPTP/L2TP

  • PPTP and L2TP
    • Theory
    • Comparison
  • PPTP Client configuration + LAB
    • Client Setup
    • Set profile
    • Dial-on-Demand
    • Add Default Route and static routes


  • PPTP Server configuration + LAB
    • Enable server
    • Setup profiles
    • Add clients to /ppp secret
    • Set static interfaces for clients
  • L2TP Client configuration + LAB
    • Client setup
    • Configure profile
    • Dial-on-Demand
    • Add Default Route and static routes
  • PPTP Server configuration + LAB
    • Enable server
    • Set profiles
    • Add clients to /ppp secret
    • Set Static interfaces for clients




Modulo 3

PPPoE

  • PPPoE server and client
    • Theory
    • Usage environment
    • Comparison to othe PPP protocols
  • PPPoE client configuration + LAB
    • Client setup
    • Select interface
    • Service name
    • Configure profile
  • PPPoE Server configuration + LAB
    • Enable PPPoE server
    • Set profiles
    • Add clients to /ppp secret
    • Add Static interfaces for clients
    • Secure server by removing any IP address from PPPoE server
    • interface



  • Encryption + LAB
    • Set profile without encryption
    • Set profile with encryption
    • Configure PPPoE client without encryption
  • Interface ECMP
    • set ECMP routes for ppp interfaces



Modulo 4

PPP Bridging

  • L2TP and EoIP + LAB
    • Set L2TP tunnel
    • Set EoIP tunnel
    • Create bridge and add necessary interfaces to ports
    • Confirm you have Ethernet connectivity between remote nodes
  • L2TP and VPLS + LAB
    • Set L2TP tunnel
    • Set VPLS tunnel
    • Create bridge and add necessary interfaces to ports
  • L2TP and BCP + LAB
    • Set L2TP tunnel
    • Use BCP to bridge PPP interface
    • Add to bridge necessary interface
  • Multilink Protocol
    • Enable Multilink by specifying correct MRRU settings
    • Disable Mangle rules for MSS adjustment


  • MLPPP [optional]
    • Setup client and specify multiple interfaces for one client
    • Set PPPPoE server with MLPPP support







Modulo 5

IPSec

  • Introduction
    • Theory and concepts
    • Comparison to other VPN protocols
  • IPSec Peer
    • Use different authentication methods
    • IPSec exchange modes
    • Encryption and Hash algorithms
    • NAT-Traversal
    • Lifetime and Lifebytes
    • DPD protocol
  • Policy
    • IPsec protocol and action
    • Tunnels
    • Generate dynamic Policy
  • Proposal
    • Encryption and Authentication algorithms
    • Lifetime
    • PFS
  • Installed-SA
    • Flush SA


  • Create IPSec between two routers with NAT + LAB
    • Set peer
    • Set policy
    • Set NAT rules
    • Confirm the secure link is established






Modulo 6

HotSpot

  • Introduction
    • Concepts
    • Usage environments
    • Setup HotSpot with default settings + LAB
  • HotSpot Login Methods + LAB
    • HTTP CHAP/PAP
    • MAC
    • Cookie
    • HTTPS
    • Trial
    • RADIUS
  • Users + LAB
    • Add users
    • Set MAC-address for user
    • Set MAC-address for username
    • Limit Uptime and Limit Bytes In/Out
    • Reset limits for user
  • Monitor Users
    • Host Table
    • Active Table
    • SNMP for usersv
  • Profile + LAB
    • Keepalive timeout
    • Shared users
    • Rate-Limit
    • Address-list
    • Incoming/Outgoing filter
    • Incoming/Outgoing Packet Mark
  • Bypass HotSpot
    • walled-garden
    • walled-garden ip
    • ip-binding


  • Customize HotSpot + LAB
    • Advertisement
    • Customize pages














Modulo 7

RADIUS

  • RADIUS client + LAB
    • add radius client
    • set service
    • use-radius for the specific service
  • RADIUS server
  • User Manager + LAB
    • Install the latest user-manager
    • Add routers
    • Add users
    • Set profile
  • RADIUS incoming